5110850460 Piston Ring for MTU 396 Series
5110850460 Piston Ring for MTU 396 Series
| Part No. | 5110850460 |
| Model | MTU 396 Series |
| Application | Piston Ring Set — Exhaust turbocharger |
Need Help? Contact Us
✉ [email protected] 💬 WhatsApp: +86 185 7493 8126 Reply within 24 hours on working daysProduct Description — Part No. 5110850460
| Pos | Part No. | Designation | Qty | Unit | Measurement |
|---|---|---|---|---|---|
| 000 | 5110201108 | EXHAUST TURBOCHARGER | 1 | EA | |
| 01 | 5110803201 | BEARING HOUSING | 1 | EA | |
| 02 | 5119910060 | DOWEL PIN | 1 | EA | |
| 03 | 000007005115 | DOWEL PIN | 1 | EA | 5 M6 X 18 |
| 04 | 5110820226 | HEAT SHIELD | 1 | EA | |
| 05 | 5110812603 | HEAT SHIELD | 1 | EA | |
| 06 | 5110252210 | BEARING | 1 | EA | |
| 07 | 700429042001 | O-RING | 1 | EA | 42 X 3 |
| 08 | 000472034000 | SNAP RING | 2 | EA | 34 X 1.5 |
| 09 | 5110250052 | WASHER | 2 | EA | |
| 10 | 5110250050 | BEARING BUSHING | 2 | EA | |
| 11 | 5110809821 | TURBINE WHEEL | 1 | EA | |
| 12 | 5110250276 | WASHER | 1 | EA | |
| 13 | 5110200412 | THRUST BEARING | 1 | EA | |
| 14 | 5110251476 | WASHER | 1 | EA | |
| 15 | 5110212814 | COMPRESSOR HOUSING | 1 | EA | |
| 16 | 700425000049 | PLATE | 1 | EA | 39 |
| 17 | 001476003017 | GROOVED PIN | 2 | EA | 3 X 8 |
| 18 | 5110200278 | VALVE | 2 | EA | |
| 19 | 000472020000 | SNAP RING | 2 | EA | 20 X 1 |
| 20 | 5110252110 | RING CARRIER | 1 | EA | |
| 21 | 5110850560 | PISTON RING | 1 | EA | |
| 22 | 5110850460 | PISTON RING | 1 | EA | |
| 23 | 5100850060 | PISTON RING | 2 | EA | |
| 24 | 700429105001 | O-RING | 1 | EA | 105 X 3.5 |
The 5110850460 Piston Ring is the piston ring set listed for the MTU Series 396 engine. This page covers what the part does, where it sits in the exhaust turbocharger, how to confirm the number against your own engine, and how we supply it. We also hold the seals, gaskets and fasteners normally renewed at the same time, so one enquiry can cover the whole job.
In the factory parts list for this engine the number is listed at position 22 of drawing E095118a2, with a quantity of 1 per assembly.
What the Piston Ring Does on the MTU 396
The ring set seals combustion gas against the liner, controls the oil film and stabilises the piston in the bore. The top compression ring takes the gas load, the second ring scrapes and assists sealing, and the oil control ring returns surplus oil to the sump.
Rings lose tension and wear on the face as the bore polishes. The result is blow-by, oil consumption, hard starting and a crankcase that breathes heavily. Rings are also replaced after any overheating, after a piston seizure, or whenever the liner is renewed.
Where 5110850460 Sits in the Engine
In the parts catalogue this number sits in the Exhaust turbocharger group, drawing E095118a2. Because MTU built this series in several ratings and configurations, the same component can be fitted in different positions from one engine to the next. The table above lists the quantities as published for this drawing.
The drawings for this number list it for 12V396TB14, 12V396TB94, 12V396TE14, 12V396TE74, 12V396TE74L, 12V396TE84, 12V396TE84/94, 12V396TE84K, 12V396TE94, 16V396TB14.
Parts Normally Renewed With 5110850460
Rings are matched to the liner and the piston groove. Fit them with a checked or new liner, clean grooves and the correct end gap, and renew the liner seals at the same time.
- 5110201108 — EXHAUST TURBOCHARGER
- 5110803201 — BEARING HOUSING
- 5119910060 — DOWEL PIN
- 000007005115 — DOWEL PIN
- 5110820226 — HEAT SHIELD
- 5110812603 — HEAT SHIELD
Confirming 5110850460 Fits Your Engine
The number on the engine is the only reliable reference. Confirm the following:
- That 5110850460 appears in the parts list for your exact engine serial number
- That the designation on the engine data plate matches this piston ring set
- Whether a later revision has superseded the number fitted to your engine
- The quantity required — the table above lists the factory quantity for this assembly
Supply, Lead Time and Documentation
We quote within one working day. Items in stock leave the warehouse immediately; where a part has to be sourced, we give you the expected date before you place the order. Air and sea freight are both available, and DAP quotations show the landed cost up front. Documentation such as certificate of origin or material certificates can accompany the shipment on request.
Frequently Asked Questions
Can I fit rings without touching the liner?
Only if the bore is still within limits and correctly honed. A glazed or oval bore will not seat new rings and the engine will continue to burn oil.
Do you supply oversize rings?
Tell us the measured bore and the number on the old ring. We confirm which repair size is listed for your engine and quote accordingly.
Is 5110850460 still available?
Send the number and your engine serial number. We check current factory parts information and confirm either availability or the superseding number before you order.